Advanced laser solutions for interconnect and component production.

ProSysTM Software for ProViaTM

ProSysTM Software for RapiTrimTM

It's all about control...

pulse by pulse, via after via ... consistently, panel after panel.

ProSys system software

Intuitive graphical user interface that offers unmatched ease of use for both operators and process engineers.

All machine setup and calibration controls, job and process settings, vision and process map, status and diagnostic information - accessible with a single click or tap.

Features

Simple operator interface - load panels and just press Start.

Process map - visualize all job features in map or camera overlays.  Clearly see at a glance what and where the process is, in real time.

Fully automatic run-time calibration activates when it needs to, ensuring process stability and accuracy.

Real-time system monitoring for process integrity

Touchscreen support for all Operator interaction

Automated file conversion and job creation without operator intervention

Compatible with industry standard file formats

File conversion automation with network interface and barcode reading allows unattended job creation

Automatic multi step and multi pass processing with performance optimization

User type access levels with password protection for visibility and access to configuration, set-up and operating screens

Maintenance Tracker keeps log of all system maintenance and history, and provides prompts at maintenance intervals

Full system diagnostics and data logging for enhanced product support and predictive maintenance

Remote access through the internet allows factory support without the cost of a service visit

Multi-language selectable

Windows 64-bit architecture

Process Control

Independently control laser pulse energy and repetition rate

Drill process tools allow precise control over bite size, spiral spacing, cut direction, via size fine adjust, inner diameter,  perimeter revolutions, and repetitions

Hole sizes are not limited by the laser spot size

Punch, spiral or rout with both UV and CO2 laser process tools

Multi-step and multi-pass processing provides unlimited combinations of operations for ultimate flexibility and process optimization

Laser tool graphics show the distribution of laser spots

Quick tool process parameter evaluation using the Process Test array functions for both drilling and routing tools

Job Creation

Stand-alone utility performs file conversion and job generation

Provides a graphical map of job features and tools

Full support of industry standard input file formats including mixed drill and rout tasks within the same job

 

Map view shows features to be processed and the tool assigned to each feature.

Features

Simple operator interface - load substrates and job, then just press Start.

Process map - visualize all job components in map or camera overlays.  Clearly see at a glance what and where the process is, in real time, including          pass /  fail indication.

Visualize trims and markings in the map or camera overlay on actual resistors

Process multi-up, panelized, or individual fixtured substrates

Laser scribed marking for serialization and circuit pass / fail status

Automatic probe tip calibration for repeatable accuracy and touch-down uniformity

Probe touchdown counter can be used for predictive tip replacement

Automatic probe tip load / unload from trays

Detailed measurement data logged as part of normal operation for every resistor

Trim profile graphing for detailed process analysis

Real-time system monitoring for process integrity

User type access levels with password protection for visibility and access to configuration, set-up and operating screens

Maintenance Tracker keeps log of all system maintenance and history, and provides prompts at maintenance intervals

Full system diagnostics and data logging for enhanced product support and predictive maintenance

Remote access through the internet allows factory support without the cost of a service visit

It's all about control...

pulse by pulse, resistor after resistor ... consistently, part after part.

Process Control

Interactive graphical process library editor - no programming required

Trim and measurement tools can be shared by resistors of different sixes and orientations - minimizes setup steps

Complete flexibility with single-plunge, double-plunge, L, vernier, scan, serpentine and custom multi-leg cut trims

Settable min / max cut length limits

Independent control of laser pulse energy, repetition rate and bite size.

Job Creation

Job creation is through an interactive graphical map of components, circuit features, alignment targets, and trims

Extensive DXF and IPC-D-356 file import support automates and speeds job creation

Resistor location, orientation, values, and limits are automatically defined

Probe test points can be automatically defined from DXF metalization information

Trim and Test Results

Easily view detailed results for each component

Data logged by substrate serial number - provides off-line historical data review and tracking

Single button click performs manual retests on an individual resistor

Real-time results update during operation

Statistical data report generation

 

1051 Baxter Road, Ottawa, Ontario, Canada  K2C 3P2               Tel:  +1-613-236-8359      info@processphotonics.com

Copyright© 2016 PPI Systems Inc.  All Rights Reserved.